How to start a chainsaw "Shtil": the process of starting and review

Anonim

All chainsaws from the manufacturer "Shtil" have two-stroke engines. Their cold start is carried out by a similar algorithm. However, on sale you can find models on which there is additional equipment, it can be used to start a saw without any special effort. For this reason, the start method may differ.

Algorithm sawing institutions "Calm 180"

Image

If you are faced with the question of how to start a chainsaw "Calm", then this process can be considered on the example of the model 180. In order to carry out work on the cold, you must turn on the ignition and set the engine control lever in the lower position. In this case, the carburetor damper will block the access of air from the filter, and the throttle valve will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture entered the cylinder, and the equipment is ready for the institution. Before you start a chainsaw "Calm", you must set the control lever one position up. This will open the air damper, while the throttle valve will remain in the same position.

Starter need to pull and start. The tool will operate at higher revs, the throttle valve will be open. To set the latter to idle mode, activate the gas trigger and release it. The tool should start working normally. On the described chainsaw model, there are no additional devices that would make starting easier.

Recommendations for the institution of the saw MS 180 C

Image

This device compared to the previous one has some differences in the trigger mechanism. However, there will be no changes in the launch algorithm. The described equipment has a system that reduces the motor resistance using a spring in the saw starter.

We start a saw brand MS 211 C-BE

Image

If you also were among those consumers who thought about the question of how to start a “Shtil” chainsaw, then as an example, consider another model that was mentioned above. In it, the feed system is equipped with a hand pump, which makes it easier to start the saw on a cold one.

The instruction contains an additional clause which indicates that it is necessary to pump fuel into the carburetor before starting with a pump. Then follow the principle described for model 180.

Sawing after winter

Image

If you are faced with the question of how to start a chainsaw "Shtil" after the winter, then you should familiarize yourself with the recommendations. From consumer reviews, it can be understood that after a long downtime, some users cannot start the equipment. For a successful launch, you need to take care of the saw in advance.

Before putting it into storage, you should drain the fuel, and then start the engine and burn the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after the winter. If you still do not know how to start the “Calm 180” chainsaw correctly, then you should know that it will be easier to do this if you add the fuel mixture to the cylinder in the amount of 2 ml before running through the candle hole. You can do this with a syringe.

The establishment of a saw with a decompression valve

Image

Users sometimes ask how to start if the instrument has a decompression valve. On the model 250, there is no such. As soon as the first flash occurs, the valve will be in normal operation. The engine control lever will be set to the position when the air damper is open. The launch will continue, at the same time it is necessary to press the decompression valve again. It does not make the launch fast, but it simplifies the process and makes it comfortable, because the operator will have to put less effort into the launch.

If you are not quite sure that you know how to start a “Calm 180” chainsaw, then remember that the equipment with the valve, regardless of whether it has a hot or cold engine, must be started using the valve. This will ease the effort of cranking the engine. So you can extend the life of the starter and reduce the number of dangling laces, because these chainsaws have a greater volume of the cylinder and compression.

Review of chainsaw MS 180

Image

This model of equipment costs 11, 490 rubles. It is a household tool that will help cope with the work on the dacha. With the help of the unit you can get rid of unnecessary knots and cut down small trees. The control is single lever, and due to its low weight it is very comfortable to work with the unit.

The consumer should be aware of not only how to start a chainsaw "Calm ms 180", but also about the technical characteristics. Among others, a 35 cm tire should be distinguished, as well as an engine whose volume is 31.8 cm 3 . The volume of the oil tank is 0.15 l. The equipment weighs 3.9 kg. Model power is 2 liters. with. The capacity of the fuel tank is 0.25 liters.

Chainsaw Review "Shtil 250"

You can buy models 250 at a price that is 29, 542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. with. or 2.3 kW. The capacity of the fuel tank is 0.47 l.

Quite often, consumers before buying ask about how to start a chainsaw "Shtil 250". This was discussed above. However, this information is not the only one that should be read before using the model. Among other features should be highlighted:

  • single lever control;
  • the presence of a compensator;
  • anti-vibration system;
  • side chain tensioner.

By purchasing this model, you can carry out its quick refueling. This feature is realized by a cover that has a patented design. The operator, working with the equipment, will have reliable hand protection. Consumers especially distinguish also a toothed support, as well as a chain that guarantees high-quality and fast sawing of wood.

Conclusion

After purchasing the equipment described in the article, you should ask how to start a “Shtil” chainsaw. This information will allow you to extend the life of the tool. After all, improper handling can cause rapid wear of some parts. It is especially important to know how to prepare the unit for long downtime. This was discussed in more detail above. After reading this information, you will be able to understand how to prepare the device for winter storage.

Sometimes the characteristics of the launch to some consumers say the technical characteristics. If this can help you too, you should familiarize yourself with them. Some of them were presented above, but their full list is presented in the instructions, which must be supplied with the equipment.

Interesting Articles

Governatore della regione di Pskov 2009-2017: successi, scandali, biografia

Costume nazionale dell'Azerbaijan: descrizione

Qual è la principale moschea di Mosca? Posizione di altre organizzazioni musulmane

Da cosa muoiono i picchi e cosa no